By EQUIPMENT FOR AUTOMATION

Features:

Compatible with a wide range of materials

It is possible to feed a variety of materials such as easily scratched, thin, irregularly shaped, film, and resin.

Achieved productivity improvement stroke number of 500 SPM. (About twice that of the conventional machine NCG65)

External control

Provides communication functions and model number management loader required for external control

Interlocked ON-OFF switching is possible using the external operation function

remote cable (signal line)

Model number management

Feeding conditions for each mold can be stored in a PLC (Programmable logic controller), computer, etc., and feeding conditions can be set simply by transferring the data when changing molds

Multi feed

Feed length, speed, and number of repetitions of operation are defined as 1 step (maximum 15 steps) as 1 cycle, allowing flexible feed by repeating the operation

The feeder can be controlled from the main device such as a press using the centralized control

communication function and remote control (feeder control via signal line)

Notes

The release mechanism of this device is an air cylinder type driven by a highly responsive solenoid valve, but due to the mechanism, there is a delay in operation. To compensate for the delay in operation, we recommend using a digital cam with an automatic advance function for the release signal. In particular, when the mold positioning pin requires precise release action or when used at high SPM, be sure to use it in combination with a digital cam with automatic advance angle function

NC Grip Feeder NCG65HA Ordering Instructions

1) Material runout detection is a function that detects the presence or absence of feed material without contact using a photoelectric sensor installed on the introduction roller and output an emergency stop signal.

2) Remote is a function that allows you to control the feeder from an external device.

If you select [W] or [V], the function options [A], [B], [C], and [E] cannot be selected.

3) Models with a remote [W] switch can be controlled (single feed operation, slow forward motion, slow backward motion) by operating the attached remote switch.

4) With remote [V] cable, it is possible to control (single feed operation, slow forward motion, slow backward motion) and switch the linked [ON/OFF] state using an external signal.

5) The following functions are realized by communicating with external devices.

i) Model number management function

ii) Multi-feeding function [Example: Repeatedly feeding sets of different feed lengths (20mm - 2 times, 45mm - 3 times, 55m - 2 times)]

6) The PLC communication functionallows operation under the feeding conditions set in the device memory without the need to install communication software. (RS422 communication) function The optional PLC communication functions [A], [B], and [C] include the [remote [V] (with cable)] function and cable.

7) A loader for model number management and a loader cable are included.

8) [E] Model number management function (serial communication specification) allows setting of feeding conditions through communication (RS232C) with external devices such as PLC and personal computer. [E] Model number management function (serial communication specification) includes the [Remote [V] (with cable)] function and cable.

Specification:

Note 1: Air pressure is the value under the condition of 0.4MPa.

Note 2: Weight including the main body and controller.

        Number of strokes for feed length

  

1: Value for test material SPCC65w x 0.5t, feed rate 99. Applicable to material cross-sectional area (width x thickness) of 32mm² or less.

2: Value for test material SPCC65w x 1.0t, feed rate 89. Applicable to material cross-sectional area of ​​65mm² or less.

3: Value for test material SPCC65w x 1.0t, feed rate 99. Applicable to material cross-sectional area of ​​65mm² or less.

4: Value for test material SPCC200w x 1.0t, feed rate 99. Applicable to material cross-sectional area of ​​200mm² or less.

 

NCG65HA (maximum material width 65mm)

NCG65HA main body

• Timing belt drive system
• Material thickness 0.1~1.0mm
• Maximum feed length 80mm

NCG65HA operation panel

NCG65HA controller

• The controller is freestanding and can be moved to a location where it is easy to operate.
• Attached cable
  • Power cable length: 6m
  • Press cable length: 6m
  • Connection cable length with NCG main unit: 3m

Mounting bracket for NCG65HA

NCG65HA dedicated mounting bracket Overview

• It can be easily attached to press machines, etc.
• The position of NCG65HA can be adjusted forward, backward, up and down.
• For NCG65HA only.

NCG65HA dedicated mounting bracket dimensions

 

NCG65HA dedicated mounting bracket ordering instructions

air control unit

Air control unit overview

• This is an auxiliary device that removes harmful substances contained in compressed air and maintains a constant air pressure.
• This is a unit that combines a filter with a filtration rate of 5μm, a microfilter with a filtration rate of 0.3μm, and a pressure reducing valve.
• Be sure to use a filter with a filtration rating of 0.3μm for NCG65HA.

Air control unit ordering instructions

Membrane air dryer (with dehumidification function)

• Membrane air dryers (with dehumidification function) are ideal for use in humid environments.
• Please use in combination with an air control unit or pressure reducing valve.

Membrane air dryer (with dehumidification function) Ordering instructions